Please Read Before Purchase and Installation



SEVERE WARNING - Electrolysis of water generates Oxyhydrogen ( HHO ) gas, a

very flammable / explosive gas. Never put an open flame or spark in front of any

Oxyhydrogen ( HHO ) gas generator device output opening. The device WILL

explode, GUARANTEED!

Just because you are producing Oxyhydrogen ( HHO ) gas out of WATER the most safe

and seemingly harmless substance on the planet it does not mean that it is safe or

harmless. This Oxyhydrogen ( HHO ) gas generator device is NOT a toy and should

Tools Required

1) Wire Cutters

2) Wire Strippers

3) Wire Terminal Crimper

4) ½” Box Open End Wrench

5) ½” Drill ( Corded or Cordless )

6) ½” Steel twist drill bit 
   (for dash LED switch "OR" use under dash kit available at any local auto parts store)

7) 3/8” Steel twist drill bit

8) Razor Knife

9) 1 Gallon “Distilled White Vinegar”

10) 1 Gallon “Distilled Water”

Component Location

1) Locate areas for HHO gas generator, bubbler spark arrester away from

moving parts and excessive heat from exhaust system or clearances that may

cause damage or hazardous conditions when components are installed. See

“Typical Installation “ ( PAGE 6 )

2) See “Typical Wiring Diagram” ( PAGE 5 ) for electrical component

placement of fuse block, relay, switch and electrical wiring harness

connections.

3) Locate the electric fuel pump fuse and wiring for switch power to energize the

control relay when motor is running. An “ADD-A-CIRCUIT” device may be

needed if the fuel pump wire or factory fuel pump crash switch is not accessible to tap into.

The switch installed is a safety device to turn the Oxyhydrogen ( HHO ) gas

generator totally off.

Parts Required For Mounting ( NOT SUPPLIED )

1) Bracket additions or modifications may be required for installation of some

components, including screws and fasteners. Every installation is different and

may require some thought prior to installation. Any items required should be

available at your local hardware store.

HHO Generator Assembly

1) Thru the metal “U” Generator bracket install (1) ¾” Black Plastic Street elbow

use supplied pipe sealant liberally on pipe threads and tighten hand tight. Install
(1) 90 Degree ½” hose fittings.use supplied pipe sealant liberally on pipe threads
and tighten hand tight. Install (1) "Pop Off - Filler" elbow with rubber relief plug
( #4 rubber plug w/ leash ) that will have no hose connection, "FIRST" place one
side of rubber plug leash around "U" Generator bracket use supplied pipe sealant
liberally on elbow pipe threads and tighten hand tight
"DO NOT OVER TIGHTEN PIPE FITTINGS" hand tighten only !!!!

Component Installation

1) Install Oxyhydrogen ( HHO ) gas generator add “White Distilled Vinegar” 2

inches above internal plates. Install Bubbler Spark Arrester add “Distilled

Water” 1 inch above inside bottom of 3/8” bubbler tube

2) Install ½” hose between Oxyhydrogen ( HHO ) gas generator and Bubbler

Spark Arrester input connector ( bubbler “input” uses interior tube)

3) Install 3/8” hose between Bubbler Spark Arrester and engine Fuel Injection

Throttle Body. Remove Factory plastic or rubber air intake ducting to drill

3/8” hole as close as possible to Throttle Body for hose installation, care must

be taken to minimize any debris inside intake ducting. Push 3/8” hose inside

air intake ducting “1 inch” or to center of ducting. Vehicles that are naturally

aspirated or with carburetors install 3/8” hole into air cleaner housing.

4) Install Wiring Harness, attach “Fuse Block” near Battery attach control Relay,

connect “RED” and “BLACK” wires to Oxyhydrogen ( HHO ) gas generator.

5) Drill ½” hole in dashboard and install switch "OR" add a under dash switch 
kit available at any auto parts store, drill 3/8” hole thru firewall and
install rubber grommet run blue wire from relay to switch. Installation of both

items require drilling holes, be extremely careful of where you drill, check

opposite side carefully for obstructions or objects that may be in the way.

Connect the blue wire from the relay to center terminal “load” on the switch

the black wire from the switch top ( LED Up ) terminal to Ground.

1) Every 300 miles change the “White Distilled Vinegar” inside of

Oxyhydrogen ( HHO ) Gas Generator adding only distilled water as levels 
decrease indicated in last step below because the anode and cathode plate
conditioning period "continues" until the plates have turned a
"GOLDEN or HONEY BROWN COLOR" 
(you will also see the Electrolyte color change from a dark blue to a light red)
at that point the conditioning period is over and now maximum
HHO production can be achieved. Please continue to next step.

2) After every 2,000 miles change “White Distilled Vinegar” inside of the

Oxyhydrogen ( HHO ) Gas Generator and “Distilled Water” inside Bubbler

Spark Arrester. Maintain fluid levels inside Oxyhydrogen ( HHO ) Gas

Generator and Bubbler Spark Arrester between changes with “Distilled

Water” only, no need to use more “White Distilled Vinegar” except at the

2,000 mile marks or if the electrolyte gets heavy with particulate matter.

3) "HHO GENERATOR" fluid level – Maximum - 2” above anode & cathode plates. 
                                                    Minimum - Top of anode & cathode plates.

"BUBBLER ARRESTER" fluid level – Maximum - 1” above inside bottom of 3/8” tube
                                                  Minimum - 1/2" above inside bottom of 3/8" tube

"NEVER RUN THE GENERATOR WITHOUT FLUIDS INSIDE"